logo
Most Viewed Last 7 Days
436MHz DATV Up-Converter (392)
DVB-S USB rx (273)
Weather Sat Images (112)
DigiLite (77)
IPTV (77)
MK808/PVRUSB2/DigiLite (70)


Cluster Activity

Spots per uW band today:
UK spotter or spotted only.

Solar data:
SFI
76
A-Index
9
K-Index
2
Exp.K
0
Sunspots
14
Activity
qui
GMF
qui
Aurora?
no

My Weather

Date:19/11/17 Time:12:21
Temp:9.5C
Wind Speed:0mph
Wind Dir:247deg
Pressure:1020.99mB
Humidity:118%
Dew Point:13.1C
UKHASnet
77GHz Doppler Module

After watching a video from Shariar (of The Signal Path) on youtube about a 77GHz adaptive cruise control module for a car i thought i would have a look at one myself.
Link here: https://www.youtube.com/watch?v=8af9YVIqhRk

There are lots of versions of these modules available and little information out there on the web, finding the best one is not possible yet due to price, i picked up a used one off ebay rather cheaply compared to the usual price around ?150 but these cheap ones are rare!
The 77GHz ones appose to the 24GHz ones appear to have '9G768' in the part number but i cant guarantee this!
I used the FCC website and entered some of the fcc numbers there to find out what frequency they operated on.

They usually go in the front of a vehicle bumper to monitor other obstacles as the adaptive cruise control unit, they are well sealed for protection against the weather but the one i bought was easy enough to get into.
There were three pcb's inside, one was the antenna, some sort of dipole array and there was an RF board and a DSP/CAN interface board.

Inside RF Board




Inside Antenna Board



The DSP board is difficult to remove due to it being soldered onto a fixed connector, the RF/Antenna part is either side of an aluminium block.

#photo#

I have spent a lot of time trying to figure out how the boards work, a lot of it is still unknown but i have some information which maybe useful to anyone else trying to use one of these modules for 76GHz which was my intention :-)

The main high frequency part is on a square substrate around 1" square. All the devices are just bare die soldered down with no markings. This substrate is then wire bonded to the rest of the RF board.

mmWave section



I still have no idea how the frequency control works as there is no 'regular' PLL ic involved but there is a 1.6GHz reference saw oscillator and a prescaled output of the high frequency(?) vco at around the same frequency.
A CPLD device is on the board but this does not appear to be used as the PLL because the prescaled output does not route to the chip in any way.
There are 8 rx ports and 4 tx ports to the antenna, rf switches on the RF part are clearly seen.

Here is my best guess at the parts on the mmWave section:

mmWave Best Guess with Voltages



RF Board Header connections:
Header Pin-out so far




Status 16/8/2017:
I can power it up
I can tune the VCO
I seem to be able to select an antenna port (logic level from the Xilinx cpld chip)
Problem is when i select an Antenna port on Tx there appears to be no output...
No work has been done via the CAN bus or on the DSP board, although i do have a CAN interface chip to play about with.

The hope here is to be able to enable it with the dsp board connected and measure the control voltages to the mmwave section.... Unfortunately i have killed the DSP board psu when probing about :-(

Antenna gain on narrowest beam is specified as around 20dB and ERP 1.5W so the Tx must be in the region of 10-20mW which would be useful at 76GHz.

Project currently on hold but if anyone has any ideas they are most welcome!!












Last page added:16/08/17 15:45
M0DTS.co.uk